|
|
|
|
 |
 |
| cold wire feed . feed units(WF-1, WF-3) . hand held torches . machine torches | ||
 |
 |
hand held torches |
|
Semiautomatic TIG torches are hand torches with the added capability of delivering a continuous filler wire directly to the weld puddle. This greatly simplifies the skill level required as compared with manual feeding the filler rod. These torches are used in conjunction with the WF1 and WF3 wire feeders. |
|
CWH PENDANT |
Pendant Unit Used in conjunction with TIG torch |
 |
|
|
|||
|
CWHTL312 |
water cooled 350 amp ACHF or DCSP @ 100% 8 in (20.3 cm) 5 oz (141 gm) 3 Series Accessories/Consumables |
 |
|
|
CWH3512 |
water cooled 400 amp ACHF or DCSP @ 100% 9-1/2 in (24.1 cm) 6-1/2 oz (184 gm) 3 Series Accessories/Consumables |
||
| CWH1812 |
water cooled 180 amp ACHF or DCSP @ 100% 8-1/8 in (20.6 cm) 3-1/2 oz (99 gm) 8 Series Accessories/Consumables |
 |
|
| CWH2312 |
water cooled 300 amp ACHF or DCSP @ 100% 8-1/4 in (20.9 cm) 3-3/4 oz (106 gm) 2 Series Accessories/Consumables |
 |
|
|
Feeding Difficult Wires - Bracket Extensions Due to the nature of certain wires it may be difficult to feed a wire through the length of the feed cable and through the curved wire guide. Friction and drag may put too much resistance on the wire when it is forced through the curved wire guide. Typically this is encountered when using very small diameter soft wires and large diameter hard wires. To alleviate this problem a wire guide extension bracket is recommended. This will allow the use of a straight wire guide in place of the curved wire guide. This will eliminate resistance on the wire. In addition to the use of the wire guide extension bracket, it is important to keep the feed cable as straight as possible. |
|
PART # 3-WGBX-60 |
|
|
|
|
RECOMMENDED COLD WIRE CONDUIT AND WIRE GUIDES |
|||||||
| TIG TORCH | WIRE SIZE | WIRE TYPE |
PART NUMBER |
||||
| WIRE CONDUIT |
WIRE GUIDE (TUBE & TIP) |
TUBE | TIP | BRACKET EXTENSION | |||
|
BODY MOUNTED:
|
.023(.5mm) - .030(.8mm) | HARD | CW-FC | CWG030B | CWGB | CWT030 | |
| .023(.5mm) - .030(.8mm) | SOFT | NOT RECOMMENDED | N/A | N/A | N/A | ||
| .035 (.9mm) | HARD | CW-FC | CWG035B | CWGB | CWT035 | ||
| .035 (.9mm) | SOFT | CW-FCN | CWG035B | CWGB | CWT035 | ||
| .045 (1.1mm) | HARD | CW-FC | CWG045B | CWGB | CWT045 | ||
| 3/64 (1.2mm) | SOFT | CW-FCN116 | CWG116B | NONE | NONE | 3-WGBX-60 | |
|
FRONT MOUNTED:
|
.023(.5mm) - .030(.8mm) | HARD | CW-FC | CWG030H | CWGH | CWT030 | |
| .023(.5mm) - .030(.8mm) | SOFT | NOT RECOMMENDED | N/A | N/A | N/A | ||
| .035 (.9mm) | HARD | CW-FC | CWG035H | CWGH | CWT035 | ||
| .035 (.9mm) | SOFT | CW-FCN | CWG035H | CWGH | CWT035 | ||
| .045 (1.1mm) | HARD | CW-FC | CWG045H | CWGH | CWT045 | ||
| 3/64 (1.2mm) | SOFT | CW-FCN116 | CWG116H | NONE | NONE | 3-WGBX-60 | |
| 1/16 (1.6mm) | HARD | CW-FC116 | CWG116H | NONE | NONE | 3-WGBX-60 | |
| 1/16 (1.6mm) | SOFT | CW-FCN116 | CWG116H | NONE | NONE | 3-WGBX-60 | |
|
SEPARATE MACHINE AND HAND HELD FEED UNITS:
|
.023(.5mm) - .030(.8mm) | HARD | CW-FC | CWG030HS | CWGHS | CWT030 | |
| .023(.5mm) - .030(.8mm) | SOFT | NOT RECOMMENDED | CWH030HS | CWGHS | CWT030 | ||
| .035 (.9mm) | HARD | CW-FC | CWG035HS | CWGHS | CWT035 | ||
| .035 (.9mm) | SOFT | CW-FCN | CWG035HS | CWGHS | CWT035 | ||
| .045 (1.1mm) | HARD | CW-FC | CWG045HS | CWGHS | CWT045 | ||
| 3/64 (1.2mm) | SOFT | CW-FCN116 | CWG116HS | NONE | NONE | ||
| 1/16 (1.6mm) | HARD | CW-FC116 | CWG116HS | NONE | NONE | ||
| 1/16 (1.6mm) | SOFT | CW-FCN116 | CWG116HS | NONE | NONE | ||
 |
||
| home . contact . representation . technical information . pricing |
© CKWORLDWIDE, INC 2005 |
|
